300-410資格取得講座、300-410日本語版復習資料

Wiki Article

ちなみに、MogiExam 300-410の一部をクラウドストレージからダウンロードできます：https://drive.google.com/open?id=1JejmmjUAUZEp9AcQH2AzvH9ukSeCqTl4

MogiExamの問題集を購入したら、あなたの試験合格率が100%を保証いたします。もし300-410試験に失敗したら、弊社が全額で返金いたします。

Cisco 300-410 試験は、企業ネットワークで高度なルーティングとサービスを実装するプロフェッショナルのスキルと知識を検証する認定試験です。ネットワークエンジニアやアーキテクトのスキルを強化したい人々にとって、最も人気のある試験の1つです。

Cisco 300-410試験は、Implementing Cisco Enterprise Advanced Routing and Servicesとしても知られており、企業環境で高度なルーティングとサービスの実装と管理能力をテストする認定試験です。この試験は、Cisco Certified Specialist - Enterprise Advanced Infrastructure Implementation認定パスの一部です。

>> 300-410資格取得講座 <<

300-410日本語版復習資料 & 300-410最新テスト

今は時間がそんなに重要な社会でもっとも少ないお時間を使って300-410試験に合格するのは一番よいだと思います。MogiExamが短期な訓練を提供し、一回に君の300-410試験に合格させることができます。試験に失敗したら、全額で返金いたします。

Cisco Implementing Cisco Enterprise Advanced Routing and Services 認定 300-410 試験問題 (Q512-Q517):

質問 # 512
Refer to the exhibit.

An engineer is trying to configure local authentication on the console line, but the device is trying to authenticate using TACACS+ Which action produces the desired configuration?

正解：B


質問 # 513
Configure individual VRFs for each customer according to the topology to achieve these goals :


R1




R2




SW1



SW2



SW3






正解：

解説：
See the solution below in Explanation.
Explanation:
Solution:
Use cu-red under interfaces facing SW1 & SW3:
On R1:
interface Ethernet0/0
ip vrf forwarding cu-red
ip address 192.168.1.254 255.255.255.0
Check reachability to SW1:
R1#ping vrf cu-red 192.168.1.1
Type escape sequence to abort.
Sending 5, 100-byte ICMP Echos to 192.168.2.1, timeout is 2 seconds:
!!!!!
Success rate is 100 percent (5/5), round-trip min/avg/max = 1/1/1 ms
On R2:
interface Ethernet0/0
ip vrf forwarding cu-red
ip address 192.168.2.254 255.255.255.0
Check reachability to SW3:
R2#ping vrf cu-red 192.168.2.1
Type escape sequence to abort.
Sending 5, 100-byte ICMP Echos to 192.168.1.1, timeout is 2 seconds:
!!!!!
Use vrf cu-green for SW2 & SW4:
On R1:
interface Ethernet0/1
ip vrf forwarding cu-green
ip address 192.168.20.254 255.255.255.0
Test reachability to SW2:
R1#ping vrf cu-green 192.168.20.1
Type escape sequence to abort.
Sending 5, 100-byte ICMP Echos to 192.168.22.1, timeout is 2 seconds:
!!!!!
Success rate is 100 percent (5/5), round-trip min/avg/max = 1/1/1 ms
On R2:
interface Ethernet0/1
ip vrf forwarding cu-green
ip address 192.168.22.254 255.255.255.0
Test reachability to SW4:
R2#ping vrf cu-green 192.168.22.1
Type escape sequence to abort.
Sending 5, 100-byte ICMP Echos to 192.168.20.1, timeout is 2 seconds:
!!!!!
Success rate is 100 percent (5/5), round-trip min/avg/max = 1/1/1 ms
On R1:
interface Ethernet0/2.100
mpls ip
!
interface Ethernet0/2.200
mpls ip
!
Configure BGP:
router bgp 65000
neighbor 10.10.10.2 remote-as 65000
neighbor 10.10.20.2 remote-as 65000
!
address-family vpnv4
neighbor 10.10.10.2 activate
neighbor 10.10.20.2 activate
exit-address-family
!
address-family ipv4 vrf cu-green
redistribute connected
exit-address-family
!
address-family ipv4 vrf cu-red
redistribute connected
exit-address-family
!
R1(config)#ip vrf cu-red
R1(config-vrf)#route-target both 65000:100
!
R1(config)#ip vrf cu-green
R1(config-vrf)#route-target both 65000:200
On R2:
interface Ethernet0/2.100
mpls ip
!
interface Ethernet0/2.200
mpls ip
!
router bgp 65000
neighbor 10.10.10.1 remote-as 65000
neighbor 10.10.20.1 remote-as 65000
!
address-family vpnv4
neighbor 10.10.10.1 activate
neighbor 10.10.20.1 activate
exit-address-family
!
address-family ipv4 vrf cu-green
redistribute connected
exit-address-family
!
address-family ipv4 vrf cu-red
redistribute connected
exit-address-family
R2(config)#ip vrf cu-red
R2(config-vrf)#route-target both 65000:100
!
R2(config)#ip vrf cu-green
R2(config-vrf)#route-target both 65000:200
Verification:
From SW1 to SW3:
SW1#ping 192.168.1.1
Type escape sequence to abort.
Sending 5, 100-byte ICMP Echos to 192.168.1.1, timeout is 2 seconds:
!!!!!
Success rate is 100 percent (5/5), round-trip min/avg/max = 1/1/1 ms
But can't Reach SW2 or SW4 in VRF cu-green:
SW1#ping 192.168.22.1
Type escape sequence to abort.
Sending 5, 100-byte ICMP Echos to 192.168.22.1, timeout is 2 seconds:
U.U.U
Success rate is 0 percent (0/5)
SW1#ping 192.168.20.1
Type escape sequence to abort.
Sending 5, 100-byte ICMP Echos to 192.168.20.1, timeout is 2 seconds:
U.U.U
Success rate is 0 percent (0/5)
Same Test for SW2:
From SW2 to SW4:
SW2#ping 192.168.20.1
Type escape sequence to abort.
Sending 5, 100-byte ICMP Echos to 192.168.20.1, timeout is 2 seconds:
!!!!!
Success rate is 100 percent (5/5), round-trip min/avg/max = 1/1/1 ms
But can't Reach SW3 or SW1 in VRF cu-red:
SW2#ping 192.168.1.1
Type escape sequence to abort.
Sending 5, 100-byte ICMP Echos to 192.168.1.1, timeout is 2 seconds:
U.U.U
Success rate is 0 percent (0/5)
SW2#ping 192.168.2.1
Type escape sequence to abort.
Sending 5, 100-byte ICMP Echos to 192.168.2.1, timeout is 2 seconds:
U.U.U
Success rate is 0 percent (0/5)
Both R1 & R2 has separate tables for VRFs cu-red and cu-green.


質問 # 514
Refer to the exhibit.

The OSPF routing protocol is redistributed into the BGP routing protocol, but not all the OSPF routes are distributed into BGP Which action resolves the issue?

正解：C

解説：
If you configure the redistribution of OSPF into BGP without keywords, only OSPF intra-area and inter-area routes are redistributed into BGP, by default. You can use the internal keyword along with the redistribute command under router bgp to redistribute OSPF intra- and inter-area routes.
Use the external keyword along with the redistribute command under router bgp to redistribute OSPF external routes into BGP.
-> In order to redistribute all OSPF routes into BGP, we must use both internal and external keywords. The full command would be (suppose we are using OSPF 1):
redistribute ospf 1 match internal external
Note: The configuration shows match internal external 1 external 2. This is normal because OSPF automatically appends "external 1 external 2" in the configuration. In other words, keyword external = external 1 external 2. External 1 = O E1 and External 2 = O E2.
Reference:
https://www.cisco.com/c/en/us/support/docs/ip/border-gateway-protocol-bgp/5242-bgp-ospf-redi s.html


質問 # 515

Refer to the exhibit. The remote server is failing to receive the NetFlow data Which action resolves the issue?

正解：D

解説：
From the exhibit we see there are two flow monitors: the first one "FLOW-MONITOR-1" has been configured correctly but the second one "v4_r1" was left empty andinterface E0/0.1 is using it. So the remote server does not receive any NetFlow data.


質問 # 516
Refer to the exhibit.

Refer to the exhibit An engineer must connect the Reno and Detroit spokes using DMVPN phase 2 Hub tunnel configuration is

Which configuration accomplishes the task?



正解：B


質問 # 517
......

多くの受験生がCiscoの300-410認定試験に良い成績を取らせるために、MogiExamはより良い結果までずっと努力しています。長年の努力を通じて、MogiExamのCiscoの300-410認定試験の合格率が１００パーセントになっていました。もしMogiExamのCiscoの300-410問題集を購入したら、学習教材はどんな問題があれば、或いは試験に不合格になる場合は、全額返金することを保証いたします。

300-410日本語版復習資料: https://www.mogiexam.com/300-410-exam.html

P.S.MogiExamがGoogle Driveで共有している無料の2026 Cisco 300-410ダンプ：https://drive.google.com/open?id=1JejmmjUAUZEp9AcQH2AzvH9ukSeCqTl4

Report this wiki page